Detailed Reference of all MIL-STD-810 Methods and Procedures

Here is the list of all MIL-STD-810 Methods and Procedures. This is according to version G, change notice 1 (MIL-STD-810G CN1) published on April 15, 2014.

Method No. Method No. Method Title
500 500.6 Low Pressure (Altitude)
Procedure I Storage/Air Transport
Procedure II Operation/Air Carriage
Procedure III Rapid Decompression
Procedure IV Explosive Decompression
501 501.6 High Temperature
Procedure I Storage
Procedure II Operation
Procedure III Tactical-Standby to Operational
502 502.6 Low Temperature
Procedure I Storage
Procedure II Operation
Procedure III Manipulation
503 503.6 Temperature Shock
Procedure I-A One-way Shock(s) from Constant Extreme Temperature
Procedure I-B Single Cycle Shock from Constant Extreme Temperature
Procedure I-C Multi-Cycle Shocks from Constant Extreme Temperature
Procedure I-D Shocks To or From Controlled Ambient Temperature
504 504.2 Contamination by Fluids
Procedure I Aircraft systems, full-up wheeled and track vehicles and water craft, etc
Procedure II Small arms systems, clothing, boots, gas masks, gloves, Less Than Lethal and other ammunition, binoculars, flashlights, small arms tripods, and other materiel
505 505.6 Solar Radiation (Sunshine)
Procedure I Cycling (heating and/or minimal actinic effects)
Procedure II Steady State (actinic effects)
506 506.6 Rain
Procedure I Rain and Blowing Rain
Procedure II Exaggerated
Procedure III Drip
507 507.6 Humidity
Procedure I Induced (Storage and Transit) and Natural Cycles
Procedure II Aggravated
508 508.7 Fungus
509 509.6 Salt Fog
510 510.6 Sand and Dust
Procedure I Blowing Dust
Procedure II Blowing Sand
511 511.6 Explosive Atmosphere
Procedure I Explosive Atmosphere
Procedure II Explosion Containment
512 512.6 Immersion
Procedure I Immersion
Procedure II Fording
513 513.7 Acceleration
Procedure I Structural Test
Procedure II Operational Test
Procedure III Crash Hazard Acceleration Test
514 514.7 Vibration
Procedure I General Vibration
Procedure II Loose Cargo Transportation
Procedure III Large Assembly Transportation
Procedure IV Assembled Aircraft Store Captive Carriage and Free Flight
515 515.7 Acoustic Noise
Procedure Ia Diffuse Field – Uniform Intensity Acoustic Noise
Procedure Ib Diffuse Field – Direct Field Acoustic Noise
Procedure II Grazing Incidence Acoustic Noise
Procedure III Cavity Resonance Acoustic Noise
516 516.7 Shock
Procedure I Functional Shock
Procedure II Transportation Shock
Procedure III Fragility
Procedure IV Transit Drop
Procedure V Crash Hazard Shock
Procedure VI Bench Handling
Procedure VII Pendulum Impact
Procedure VIII Catapult Launch/ Arrested Landing
517 517.2 Pyroshock
Procedure I Near-field with an Actual Configuration
Procedure II Near-field with a Simulated Configuration
Procedure III Mid-field with a Mechanical Test Device
Procedure IV Far-field with a Mechanical Test Device
Procedure V Far-field with an Electrodynamic Shaker
518 518.2 Acidic Atmosphere
519 519.7 Gunfire Shock
Procedure I Direct Reproduction of Measured Materiel Input/Response Time Trace Data Under Guidelines Provided in Method 525.1 for Time Waveform Replication (TWR)
Procedure II Stochastically Generated Materiel Input/Response Based Upon Measured Time Trace Information
Procedure III Stochastically Predicted Materiel Shock Input for Preliminary Design Based Upon Predicted
Sine-on-Random Spectrum
520 520.4 Temperature, Humidity, Vibration, and Altitude
Procedure I Engineering Development
Procedure II Flight or Operation Support
Procedure III Combined Environments Test
521 521.4 Icing/Freezing Rain
522 522.2 Ballistic Shock
Procedure I Ballistic Hull and Turret (BH&T), Full Spectrum, Ballistic Shock Qualification
Procedure II Large Scale Ballistic Shock Simulator (LSBSS)
Procedure III Limited Spectrum, Light Weight Shock Machine (LWSM)
Procedure IV Limited Spectrum, Mechanical Shock Simulator
Procedure V Limited Spectrum, Medium Weight Shock Machine (MWSM)
Procedure VI Drop Table
523 523.4 Vibro-Acoustic/Temperature
524 524.1 Freeze-Thaw
Procedure I Diurnal Cycling Effects
Procedure II Fogging
Procedure III Rapid Temperature Change
525 525.1 Time Waveform Replication
Procedure I The SESA replication of a field measured materiel time trace input/response
Procedure II The SESA replication of an analytically specified materiel time trace input/response
526 526.1 Rail Impact
527 527.1 Multi-Exciter Testing
Procedure I Time Domain Reference Criteria
Procedure II Frequency Domain Reference Criteria
528 528.1 Mechanical Vibrations Of Shipboard Materiel (Type I – Environmental And Type II – Internally Excited)
Procedure I Type I – Environmental Vibration
Procedure II Type II – Internally Excited Vibration
Posted in MIL-STD-810